COMPONENT
#691175
24V BATTERY-OPERATED
IMPACT WRENCH
INSTRUCTION MANUAL
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,
MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND
UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE TO DO
SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
FOR CUSTOMER SERVICE
POUR LE SERVICE APRÉS VENTE
OU DU CONSOMMATEUR
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE
PRODUCT, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE
DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION
AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE
REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU WOULD LIKE TO MAKE
YOUR FEEDBACK IS VITAL TO US.
87-1904-60957
KAWASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™
MOTORS CORP., U.S.A., WHICH DOES NOT MANUFACTURE OR
DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE
DIRECTED TO:
PARA EL SERVICIO
PARA EL CONSUMIDOR
©COPYRIGHT 2005 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA
1-800-590-3723
Printed in China
691175 –24V Black Cordless Impact Wrench
WORK AREA
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.
Keep your work area clean and well lit. Cluttered benches and dark areas
invite accidents.
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
Do not operate power tools in explosive atmospheres, such as in the pres-
ence
of
NOTE provides additional information that is useful
for proper use and maintenance of this tool. If a
NOTE is indicated make sure it is fully understood.
flammable liquids, gases or dust. Power tools create sparks which may ignite
the dust or fumes.
Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control.
IMPORTANT SAFEGUARDS
ELECTRICAL SAFETY
People with electronic devices, such as pacemakers, should consult their
physician(s) before using this product. Operation of electrical equipment in
close proximity to a heart pacemaker could cause interference or failure of
the pacemaker.
Do not abuse the cord. Never use the cord to carry the tool. Keep the cord
away from heat, oil, sharp edges, or moving parts. Replace damaged cords
immediately. Damaged cords may create a fire.
WARNING: Some dust created by power sanding, sawing, grinding, drilling and
other construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
A battery operated tool with integral batteries or a separate battery pack
must be recharged only with the specified charger for the battery. A charger
that may be suitable for one type of battery may create a risk of fire when used with
another battery.
Some examples of these chemicals are:
• Lead from lead-based paints.
Use battery operated tool only with specifically designated battery pack. Use of
any other batteries may create risk of fire.
• Crystalline silica from bricks and cement and other masonry products,
and arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as dust masks that are
specially designed to filter out microscopic particles.
WARNING: Handling the power cord on this product may expose you to lead, a
chemical known to the State of California to cause cancer and birth defects or
other reproductive harm. Wash hands after handling.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
3
4
When battery pack is not in use, keep it away from other metal objects like:
paper clips, coins, keys, nails, screws, or other small metal objects that can
make a connection from one terminal to another. Shorting the battery terminals
together may cause sparks, burns or a fire.
PERSONAL SAFETY
Stay alert, watch what you are doing, and use common sense when operat-
ing a power tool. Do not use tool while tired or under the influence of drugs,
alcohol or medication. A moment of inattention while operating power tools
may result in serious personal injury.
Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained
tools with sharp cutting edge are less likely to bind and are easier to control.
Check for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tool’s operation. If damaged, have the tool
serviced before using. Many accidents are caused by poorly maintained tools.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose clothes,
jewelry or long hair can be caught in moving parts.
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may create a risk of injury when used
on another tool.
Avoid accidental starting. Be sure switch is in the locked or “OFF” position
before inserting battery pack. Carrying power tools with your finger on the
switch or inserting battery pack into a tool with the power switch “on” invites
accidents.
SERVICE
Tool service must be performed only by qualified repair personnel. Service or
maintenance by unqualified personnel may result in a risk of injury.
Remove adjusting keys or wrenches before turning the tool “ON”.
A wrench or a key that is left attached to a rotating part of the tool may result
in personal injury.
When servicing a tool, use only identical replacement parts. Follow instructions
in the Maintenance section of this manual. Use of unauthorized parts or failure to
follow Maintenance Instructions may create a risk of shock or injury.
Do not overreach. Keep proper footing and balance at all times. Proper foot-
ing and balance enable better control of the tool in unexpected situations.
SPECIFIC SAFETY RULES AND/OR SYMBOLS
Use safety equipment. Always wear eye protection. Dust mask, non-skid
safety shoes, hard hat, or hearing protection must be used for appropriate
conditions.
Hold tool by insulated gripping surfaces when performing an operation where the
cutting tool may contact hidden wiring. Contact with a “live” wire will also make
exposed metal parts of the tool “live” and shock the operator.
TOOL USE AND CARE
SAFETY RULES FOR IMPACT WRENCH
Use clamps or other practical ways to secure and support the workpiece to a
stable platform. Holding the work by hand or against your body is unstable and
may lead to loss of control.
Always wear safety goggles or eye protection when using this tool. Use a dust
mask or respirator for applications which generate dust.
Do not force tool. Use the correct tool for your application. The correct tool will
do the job better and safer at the rate for which it is designed.
Do not grasp the tool or place your hands too close to the spinning chuck or drill
bit. Your hand may be lacerated or may cause injury.
Secure the material being worked on. Never hold it in your hand or across your
legs. Unstable support can cause loss of control and injury.
Do not use the tool if the power switch does not turn it “ON” or “OFF”. A tool that
cannot be controlled with the switch is dangerous and must be repaired.
Position yourself to avoid being caught between the tool or side handle and walls
or posts. Should the socket or bit become bound in the work, the reaction torque
of the tool could crush your hand or leg.
Disconnect battery pack from tool or place the switch in the locked or “OFF” position
before making any adjustments, changing accessories, or storing the tool. Such
preventative safety measures reduce the risk of starting the tool accidentally.
Check to see that keys and adjusting wrenches are removed from the Cordless
Impact Wrench before switching the tool “ON”. Keys or wrenches can fly away at
high velocity striking you or a bystander.
Store idle tools out of reach of children and other untrained persons. Tools are
dangerous in the hands of untrained users.
When using the Cordless Impact Wrench, always maintain a firm grip on the tool
with both hands.
5
Hold tool by insulated gripping surfaces when performing an operation where the
cutting tool may contact hidden wiring. Contact with a "live" wire will also make
exposed metal parts of the tool "live" and shock the operator.
BATTERY
Keep the handle of the Cordless Impact Wrench dry, clean, and free from oil and
grease.
Before using battery pack, please read carefully all instructions and cautionary
markings on battery pack, battery charger and product using battery.
Do not run the Cordless Impact Wrench while carrying it at your side. A spinning
socket or bit could become entangled with clothing and injury may result.
Do not incinerate the battery pack even if it is severely damaged or is
completely worn out. The battery pack can explode.
Disconnect the plug or remove the battery pack from tool and place the switch in
the locked or “OFF” position before making any assembly adjustments, changing
accessories, performing any inspection, maintenance or cleaning procedures.
Such preventive safety measures reduce the risk of starting the tool accidentally.
Do not carry battery packs in aprons, pockets, or tool boxes, product kit
boxes, drawers, etc. with loose metal objects. battery pack terminals could
be short circuited causing damage to the battery pack, severe burns or fire.
Do not use the Cordless Impact Wrench if it has been damaged, left outdoors in
the rain, snow, wet or damp environments, or immersed in liquid.
The battery pack is Nickel-Cadmium (Ni-Cad) and is considered to be a toxic
material by the Environmental Protection Agency. Before disposing of
damaged or worn out Ni-Cad battery packs, check with your State
Environmental Protection Agency to find out about special restrictions on the
disposal of these battery packs, take them to your local recycling center for
proper disposal, or call 1-800-CLEANUP.
Maintain labels and nameplates on the Cordless Impact Wrench. These carry
important information. If unreadable or missing, contact Alltrade for a replacement.
SYMBOLS
IMPORTANT: Some of the following symbols may be used on your tool. Please
study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.
The battery is not fully charged. Before first use, the battery pack requires
3-5 hours charge time to be fully charged. Subsequent recharging needs 1 hour
for the battery to be fully charged.
SYMBOL
NAME
Volts
EXPLANATION
Voltage (Potential)
V
Always switch to a fresh battery when tool performance begins to diminish.
Severe heat is most destructive to a battery; the more heat generated, the faster
the battery loses power. A battery that gets too hot can have a shortened life.
A
Amperes
Current
Hz
W
Hertz
Watt
Frequency (Cycles per Second)
Power
Never over-discharge a battery by using the tool even after tool performance
has decreased. Do not attempt to discharge a tool’s battery by continuing to
pull on the tool trigger. When tool performance begins to diminish, stop the tool
and recharge the battery for optimal performance.
Kg
Kilograms
Alternating Current
Direct Current
Weight
Type of Current
Type of Current
Alternating or Direct Current Type of Current
Charge battery pack at ambient temperatures between 50° F – 104° F.
Earthing Terminal
Class II Construction
Minutes
Grounding Terminal
Denotes Double Insulation
Time
Time
Store tool and battery pack in locations where temperatures will not exceed
120°F. This is important to prevent serious damage to the battery cells.
min
s
Seconds
The battery pack should always be recharged when the Cordless Impact Wrench
begins to run slowly.
Diameter
Size of Drill Bits,
Grinding Wheels, etc.
No-load Rotational Speed
Revolutions, Surface Speed,
Strokes, etc. per Minute
When battery pack is not in use, keep it away from other metal objects such as
paper clips, coins, keys, nails, screws or other small metal objects that can
make a connection from one terminal to another. Shorting the battery terminals
together may cause sparks, burns, or fire.
No load speed
.../min
Revolutions per Minute
1,2,3, …
Ring Selector Settings
Speed, Torque or Position Settings
8
REMOVING / ATTACHING BATTERY PACK
REMOVE BATTERY PACK:
1. Press both release buttons on either side
of the Impact Wrench to release the bat-
tery pack.
CHARGING BATTERY PACK
BATTERY PACK
CHARGE BATTERY PACK:
1. Make sure the trigger on
the Cordless Impact
Wrench is in the “OFF”
position and remove the
battery pack from the
Impact Wrench.
2. Pull battery pack free of Impact Wrench.
ATTACH BATTERY PACK:
1. Align the raised portion of the battery pack
with the groove in the battery compart-
ment of the Impact Wrench.
2. Insert the battery pack into the
charger. Be sure that the battery
pack is fully seated in the charg-
er. Do not force.
2. Press the battery pack into place. Make
sure the latches are securely fastened. Do
not use the Impact Wrench if the battery
pack is not
RELEASE
BUTTON
3. Plug the charger into the nearest
120 volt, electrical outlet. The
indicator light will come “ON”.
BATTERY
CHARGER
seated properly.
INDICATOR LIGHTS OF CHARGER
CHARGER
Power On
The Charger is power on.
Battery -
Faulty
The battery life may end or the battery
voltage may be in extraordinary
conditions. Please unplug the charger,
then replace the battery pack.
Before using battery charger, please read carefully all
instructions and cautionary markings on battery charger, battery pack and
product using battery.
RED
Battery in High The battery pack is overheated. Please
The charger will not automatically turn “OFF” when the
battery pack is fully charged. The charging indicator light will remain “ON”
until the charger is disconnected from the electrical outlet.
Temperature
wait until the battery pack cools
down, or take it out from the charger
temporarily to be cooled off.
Battery in Low The battery pack’s temperature is too
Use only the charger which accompanied your product or direct replacement as
listed in this manual. Do not substitute any other charger. Use only Alltrade
approved chargers with your product.
YELLOW
GREEN
Temperature
low. Please wait untl the battery pack’s
temperature rises to 50°F.
Incorrect
Battery Type
The battery pack is unspecified or has
failed. Please replace the battery pack
with a new one.
Do not disassemble charger.
Do not use charger if it has been damaged, left outdoors in the rain, snow, wet
or damp environments, or immersed in liquid.
Fast Charging The battery is under Quick Charging.
The battery pack and charger heat during charging. Place the charger on a flat,
non-flammable surface away from flammable materials with at least four inches of
clearance to allow proper air circulation around the charger and battery pack.
Fully Charged The charging is completed. Please
take the battery pack out from the
charger, then unplug the charger
When the battery pack requires recharging, a 1 hour charge allows the tool to
operate at full power. A charging indicator light on the charger will illuminate to
show that charging is taking place.
from the power supply outlet.
9
10
IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES
OPERATING THE IMPACT WRENCH
When using your Cordless Impact Wrench continuously, the batteries in your bat-
tery pack will become hot. You should let a hot battery pack cool down for approxi-
mately 30 minutes before attempting to recharge. When the battery pack becomes
discharged and is hot, the red light on the charger will flash. When the battery
pack cools down, the red light will glow continuously to indicate fast charging
mode, 1-hour charge time.
Be aware that this tool is always in an operating condition
because it does not have to be plugged into an electrical outlet. Always turn the
switch “OFF” and remove the battery pack before changing bits.
VARIABLE SPEED TRIGGER SWITCH
This will occur when continuous use of your Cordless
Impact Wrench causes the battery pack to become hot. It does not occur
under normal circumstances.
Never tape the trigger switch down to provide continuous
high speed. The tool may fail under such conditions causing fire or
personal injury.
FUNCTIONAL DESCRIPTION
THIS TOOL IS CONTROLLED
BY A TRIGGER SWITCH:
3
10
7
• The speed of the Cordless Impact
Wrench depends on the amount of pres-
sure you put on the trigger.
2
11
• The more pressure you apply, the faster
5
TRIGGER
the Cordless Impact Wrench will go.
SWITCH
8
1
• Release the pressure and the Cordless
Impact Wrench will slow down.
9
6
FORWARD / REVERSE AND TRIGGER LOCK LEVER
4
CONTROLS AND COMPONENTS:
1. Variable Speed Trigger Switch
6. LED Charging Indicators
7. Anvil
Be sure the trigger is released when changing the position of the lever.
Always store the tool in the “LOCKED/OFF” position.
2. Forward/Reverse and
Trigger Lock Lever
3. Gear Enclosure
4. Release Buttons on Each Side
5. Charger
8. Comfort Rubber Grip
9. Battery Pack
ACCESSORIES:
10. 1/2" Drive Impact Socket (4)
11. 5" x 1/2" Drive Extension Bar
Always check the direction of the Cordless Impact Wrench's rotation before
use.
COMPONENT
CHARGER
BATTERY PACK
MODEL NUMBER
691173
691174
12
TO SELECT THE DIRECTIONS
OF ROTATION:
This Cordless Impact Wrench is lubricated before it
leaves the factory. This lubrication should last for the life of the tool. No
further lubrication is required.
• To select forward Cordless
Impact Wrench rotation,
press the trigger lock from
left to right flat against the
Cordless Impact Wrench
body.
Use only mild soap and a damp cloth to clean the tool. Never let any liquid get
inside the casing. Never immerse any part of the tool in a liquid. Always keep the
ventilation openings clear.
Reverse Lock Forward
TRIGGER
LOCK
Always clean the battery pack using only a dry cloth. Do not use liquids.
Always unplug the charger before cleaning it.
• To select reverse, press the
trigger lock lever in the oppo-
site direction.
Regularly clean the ventilation slots in your tool and charger using only a soft
brush or dry cloth.
• The center position locks the
tool.
Never open the Cordless Impact Wrench case, battery pack or charger. Do not
attempt to repair the Cordless Impact Wrench, battery pack or charger yourself.
Opening any of these parts will void your warranty.
INSTALLING / REMOVING SOCKET ON THE ANVIL
When removing the socket or bit from the tool, avoid
contact with skin and use proper protective gloves when grasping the socket,
bit or accessory. Accessories may be hot after prolonged use.
ACCESSORIES
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.
If you must use an extension cord, be sure that the gauge is large enough to carry
the amount of current necessary for your power tool. If not, your tool may
experience a loss of power, excessive voltage drop or overheating. The smaller the
gauge number, the heavier the cord (see table below).
When installing a socket, align the
holes in the side of the socket with the
dent pin. Press the socket on until the
dent pin engages in the hole. To remove a
socket, depress the dent pin through the
hole using a small pointed object and pull
the socket off.
RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS
TOOL CURRENT RATING
CONDUCTOR SIZE IN A.W.G
AMPERE
3-6
6-8
8-10
10-12
12-16
16-20
10FT.
18
18
18
16
25FT.
18
18
18
16
50FT.
18
18
18
14
100FT.
18
16
14
14
-
MAINTENANCE AND CLEANING
14
12
12
12
12
12
Always remove the battery pack before attempting
cleaning or maintenance.
-
13
14
SPECIFICATIONS
SPECIFICATIONS
2 YEAR LIMITED HOME USE WARRANTY
Express and Exclusive Limited Home Use Warranty to Original Retail Buyer
Alltrade Tools LLC (hereinafter "Alltrade") expressly warrants to the original retail
purchaser of the accompanying KAWASAKI™ portable power tool and no one else
all parts of the product (except those parts referred to below which are specifically
excluded from such warranty (see Exclusions)) to be free from defects in materials
and workmanship for a period of two years from original date of purchase.
Voltage
Speed
24V
0-2200 (no load) rpm
0-4400 bpm
240 ft.lbs.
Impacts Per Minute
Maximum Torque
Charger Input
Charger Output
Charging Time
Battery Type
120V
60Hz
SPECIAL WARRANTY NOTE TO CONTRACTORS AND COMMERCIAL USERS: This
Kawasaki™ portable power tool is offered as a home use tool and carries a HOME
USE WARRANTY. This tool is made for home use in the execution of
projects and repairs in and around the home. Use of the tool for COMMERCIAL
PURPOSES OR ON A JOBSITE is not covered under this warranty.
24V DC, 1.9A
Approx. 1 Hour
Ni-Cad
PROTECTING THE ENVIRONMENT
The date of purchase shall be the date of shipment to the original purchaser, or the
date the original purchaser took possession, custody or control of the product,
whichever occurred first. This warranty shall be null and void if the product or any
component thereof is modified, altered or used for any commercial purpose or on
a jobsite. This warranty does not apply to any other product and/or component
thereof manufactured or distributed by Alltrade, and does not apply to products
and/or components thereof designed, manufactured and/or assembled by others,
for which Alltrade makes no warranties whatsoever. THERE ARE NO WARRANTIES
WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.
BATTERIES
Alltrade batteries can be recharged many times. At the end of their useful life, recy-
cle batteries with due care for our environment.
Ni-Cad and Ni-MH batteries are recyclable. Take them to your local recycling center
or call 1-800-CLEANUP. Collected batteries will be recycled or disposed of properly.
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS
Warranty Performance
By purchasing the product, purchaser expressly acknowledges and agrees that their
sole and exclusive remedy under this warranty shall be strictly limited to the repair
or replacement of any covered nonconforming items or parts thereof provided that
any such nonconforming item and/or part is promptly returned to Alltrade’s facility
postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair,
1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service #310-522-9008)
within the applicable warranty period, with a written request by purchaser that
Alltrade repair and/or replace the nonconforming item and/or part. We recommend
that you keep the original product packaging in the event you need to ship the unit.
We suggest the package be insured against loss or in transit damage. When
sending your product include your name, address, phone number, dated proof
of purchase (or copy), and a statement about the nature of problem. Warranty
coverage is conditioned upon purchaser furnishing Alltrade with adequate written
proof that they are the original purchaser and of the original purchase date. Parts
returned, freight prepaid and insured, to Alltrade’s facility (see above address) will
be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if
found to be defective and subject to warranty. Alltrade retains the sole discretion
to determine whether any item or part is nonconforming and, if so, whether the
Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would
like further information on the following products, please contact Alltrade Customer
Service Department at 1-800-590-3723.
Cordless Drills/Screwdrivers
Impact Wrenches
Sanders
Jigsaws
Circular Saws
Angle Grinders
Reciprocating Saws
Routers
Rotary Tools
Corded and Cordless Multi-Purpose Tools
Wide Range of Accessories and more
15
16
item and/or part will be repaired and/or replaced. If the unit is repaired, new or
reconditioned replacement parts may be used. If Alltrade chooses to replace
the product, it may replace it with a new or reconditioned one of the same or
comparable design. The repaired or replaced unit will be warranted under the terms
of the remainder of the warranty period. Typically, a defective product that is
returned within the first 30 days after the purchase date will be replaced; for items
returned after the first 30 days and within the warranty period, covered defective
parts not subject to normal wear and tear or other exclusions will be repaired or
replaced, at Alltrade’s option. During the warranty period, Alltrade will be responsi-
ble for the return shipping charges. Alltrade’s repair and/or replacement of any non-
conforming item and/or part thereof shall constitute fulfillment of all
obligations to the purchaser. Alltrade shall not be responsible or liable for any
expense, including freight charges, or repairs made outside Alltrade’s facility, unless
expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade
bear any responsibility for loss of the unit, loss of time or rental, inconvenience,
commercial loss or consequential damages.
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES,
GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY
PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR
REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE
PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY
ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE
BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE
AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY
WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR
CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER’S
SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.
EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE
WARRANTY IS MADE WITH REGARD TO THIS PRODUCT. ALL EXPRESS AND/OR
IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE
AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE,
PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT
THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY,
GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY
OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF
ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY
EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES.
PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH
WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING
THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE
REMEDY IS AS STATED ABOVE.
Exclusions
This warranty does not cover parts damaged due to normal wear, abnormal
conditions, misapplication, misuse, abuse, accidents, operation at other than
recommended pressures or temperatures, improper storage or freight damage.
Parts damaged or worn by operation in dusty environments are not warranted.
Failure to follow recommended operating and maintenance procedures also
voids warranty.
This limited warranty does not apply to accessory items such as drill bits,
screwdriving bits, circular saw blades, jigsaw blades, grinding wheels, sanding
sheets and other related items.
DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY,
USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES,
COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO
PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS
WARRANTY.
Limitation Of Liability
IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH
OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS
REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER,
AND/OR THE EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR
OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS
REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH
DAMAGES. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,
Alltrade will not be liable for the following: labor charges, loss or damage resulting
from improper operation, maintenance or repairs made by other persons;
pre-delivery services such as assembly, oil or lubricants, and adjustment;
maintenance services that are normally required to maintain the product.
The use of other than genuine Alltrade Repair Parts will void warranty.
Warranty Disclaimers
17
18
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL
ALLTRADE’S AND/OR ITS REPRESENTATIVE(S)’ LIABILITY EXCEED THE PRICE OF
THE PRODUCT. ANY AND ALL LIABILITY CONNECTED WITH THE USE OF
THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY
PERIODS SPECIFIED ABOVE.
Limitations on Warranty Disclaimers
Some states do not allow limitations on how long an implied warranty lasts
and some states do not allow the exclusion or limitation of the incidental or
consequential damages, so part or all of the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
If your product is not covered by this warranty, please call our Customer Service
Department at 1-310-522-9008 or toll free at 1-800-590-3723 for general repair
information and charges.
19
20
|